Carbon Fibre Reinforced Nylon (Polyamide)

PA-CF

ENTHUSIAST For structural parts that need to be as light as possible

PA-CF is what you reach for when PETG or ASA isn't stiff enough and weight matters. The carbon fibre reinforcement dramatically improves rigidity and lowers weight-to-strength ratio. The tradeoff: it eats brass nozzles, requires a hardened steel hotend, and is among the most moisture-sensitive materials you'll run. High effort, high reward.

Print Settings
Nozzle Temp 260–280°C
Bed Temp 70–90°C
Chamber 50–60°C recommended
Cooling Fan 20–40%
Max Speed 60 mm/s
Heat Deflection ~180°C
Difficulty Advanced
Updated 2026-06-01
At a glance
Pros
  • Exceptional stiffness-to-weight ratio — significantly stiffer than PETG at same weight
  • Heat resistant to ~180°C — survives environments that would destroy PETG and ABS
  • Excellent fatigue resistance — holds up under repeated stress cycles
  • Low-friction surface — self-lubricating properties for mechanical parts
  • Matte, technical surface finish — looks premium straight off the printer
Cons
  • Hardened nozzle mandatory — abrasive CF will destroy brass in a single spool
  • Extreme moisture sensitivity — must be printed from an active dryer
  • Enclosure required — nylon base warps in open-air conditions
  • Expensive — 2–3× cost of PLA or PETG
  • Brittle compared to unfilled nylon — CF improves stiffness but reduces impact resistance
Overview

PA-CF is an impressive material when processed correctly. Parts that feel close to injection-molded nylon, dramatically lighter than equivalent PETG parts, with heat resistance that makes ABS look modest. The engineering tradeoffs are significant but they’re all manageable with the right setup.

The non-negotiables: hardened steel nozzle, active drying, enclosed chamber. Everything else is tuning.

The CF in PA-CF trades some of nylon’s inherent flexibility for stiffness. Pure PA12 or PA11 is more impact-resistant. PA-CF is stiffer. For brackets, tool holders, and load-bearing structural parts that need to be lightweight, PA-CF is the right call. For parts that need to flex and survive drops, consider unfilled PA12 instead.

Use it for: drone frames and mounts, automotive structural brackets, tooling fixtures, anything where PLA or PETG flex too much under load, robotics structural components.

Don’t use it for: parts that need to survive impact (use unfilled nylon), flexible parts (use TPU), parts where surface finish is critical (CF gives matte only), anything where brass nozzle output is unavoidable.

Brand Recommendations
Bambu Lab PA-CF TOP
$39.99/kg

Most beginner-accessible PA-CF. Tuned profiles for X1C. AMS Lite compatible (not standard AMS). Best starting point for Bambu users.

Polymaker PA6-CF TOP
$44.99/kg

PA6 base runs at lower temps than PA12, easier to process. Excellent rigidity. Consistent diameter. Community-validated settings widely available.

Prusament PA11 CF TOP
$59.99/kg

PA11 bio-based — less moisture absorption than PA6 or PA12. Most forgiving nylon base. Expensive but justified for demanding applications.

Fiberon PA-CF MID
$34.99/kg

Solid value. Less consistent than premium options. Good for prototyping before running expensive material.

SUNLU PA-CF BUDGET
$24.99/kg

Functional but moisture management is critical. Diameter inconsistency occasionally causes clogs. Acceptable for non-critical parts.

Troubleshooting
Nozzle wear / clogging
Cause Running CF through a brass nozzle
Fix Hardened steel nozzle is mandatory. Replace after every ~500g through non-hardened nozzles if you've already run it through one. CF is abrasive — no exceptions.
Moisture-related failures (popping, bubbling, rough layers)
Cause PA absorbs moisture faster and more aggressively than any common filament
Fix Dry at 70–80°C for 8–12 hours before use. Print from a dry box or active dryer. PA-CF stored open overnight can be unprintable by morning.
Warping
Cause Nylon base has significant shrinkage
Fix Enclosed chamber at 55°C minimum. Garolite (FR4) bed surface is the best adhesion surface for PA-CF. PEI requires glue stick. Large brim on any part with flat geometry.
Layer delamination
Cause CF particles reduce inter-layer bonding vs unfilled nylon
Fix Slow perimeter speeds. Increase layer overlap. Avoid fan on structural walls.
Under-extrusion at speed
Cause PA-CF requires more melt time than PLA — high speeds at stock flow rates cause gaps
Fix Tune max volumetric flow specifically for your hotend. PA-CF flow typically caps 20–30% below equivalent PLA speeds.
Printer Compatibility
Printer Rating Notes
Bambu X1C EXCELLENT Hardened nozzle pre-installed. AMS Lite compatible (not standard AMS — CF particles jam the hub). Best Bambu platform for PA-CF.
Bambu P1S EXCELLENT Same as X1C. P1S enclosed chamber is critical for PA-CF.
Voron 2.4 EXCELLENT Hardened steel nozzle required — Tungsten Carbide or Bondtech CHT in hardened steel. Nevermore filter recommended.
Voron Trident EXCELLENT Same as 2.4.
RatRig V-Core 3 EXCELLENT Enclosed with chamber heat. Hardened nozzle required.
Bambu A1 / A1 Mini POOR No enclosure. PA-CF will warp without a sealed hot chamber. Not recommended.
Prusa MK4 POOR Open frame. Hardened nozzle upgrade available but warping without enclosure makes PA-CF impractical.